deojn0的部落格

Before beginning, satisfy be positive that you have the essential tools. You'll demand (a) a unbelievably weeny flat-head screwdriver, (b) a undersized Phillips screwdriver, (c) and a tri-wing screwdriver. The tri-wing screwdriver can be obtained by doing an Internet investigate (Google, Yahoo!, etc.) and superficial for "Game Boy Advance Screwdriver." To my knowledge, this screwdriver cannot be bought in outlet.

If you're doing this for soul else, I recommend to the full carrying out tests the handset before fetching it isolated. Check the speakers (regular and boisterous) and the mic to be secure of straight-laced operation.

Start with the phone booth deceitful face-down in forward of you. Before you rob the battery off, you'll status to pull out the jailor covering situated straight close to the transmitting aerial. It's not the pocketable rubberised circle; rather, it's the parallelogram next to the amygdaloid edges. Just use the teeny flat-head and propel into the slither. This part is nix more than a sticker, but it may filch a petite shot to pry it off. Now displace the battery floor. You'll see a complete of 4 tri-wing screws present. Remove those and set them excursion.

Using your fingernail or the flat-head, go in circles the brim of the handset and separate the cell phone isolated. You should perceive a "snapping" rumble. Don't panic! This is right the clips emotional. There are two clips on all broadside of the phone to emancipation. After that is done, have the phone booth top side thrown and thoughtfully tow the cell phone isolated spell wiggling it. The phone should pop obscure. Sometimes one of the sidelong keys falls out spell doing this. Don't worry, all you have to do is only just visual projection it rear in and you're set.

After you get the back flattering off, you should be able to see a short market square minute opening at the top of the handset where on earth the hinges are. Look into this crack. On the authorization side, you'll see a white plastic "pop-rivet." Use your screwdriver and compress in towards the center as ably as out. You're exasperating to prod this out of the side of the electronic equipment. It takes a micro run through at first, but it will pop out. The edges may be beaten-up a little, also, but it will static go posterior into the electronic equipment once you're through with. After you get the joint out, put the support of the electronic equipment vertebrae mutually. Leave the flexible joint mendacious on the negative for now.

Congratulations! You're in the middle through with beside this cellular phone. After you've fattened putt the screws into the fund of the phone, insolent it unambiguous. You'll thought iv (4) gaoler covers circa the inner-LCD eyeshade. Just as next to the bit adjacent to the antenna, these are null more than stickers. Push as low as you can near your flat-head screwdriver and tow them out. Then takings the 4 (4) tri-wing screws out simply as you did in the posterior of the receiver.

Remember how you popped the final of the mobile off? You're going to do the same item to the frontal of the receiver. After you've gotten all 4 screws out of the phone, run your fingernail or a microscopic flat-head on all sides the hole in the fringe of the cellular phone. You'll perceive the said "snapping" sound, and later it will pop friendly resembling a car felon.

After you've staring the phone, manifestation at the hinge. You should see a least hoary portion (similar to a jigsaw riddle particle) that you can click out near your nail. Go ahead and pop that bit out. Now this should fix your eyes on familiar! Just as you did in the rear of the phone, pop this flexible joint out as capably and the protection will slip truthful off.

Now lately hold your Phillips screwdriver and transfer the speaker from the saucer. You'll see two screws. It may help out to have your hand tool magnetic so you don't mislay the screws. Put the articulator into the new sheet and regenerate the screws. Put the teensy-weensy plastic covering rear of the hole, and the put the protective covering rear onto the telephone. Push fallen on the exterior edges, and you'll comprehend the "snapping" undamaged again. That's a respectable situation. It scheme you have put it posterior equally decent.

Before you put the screws and hinges final in, this is a suitable event to swerve the receiver aft on and mental test it. When it powers up, you should comprehend the beginning wholesome. If not, supervise and sort convinced the phone is not set to jerk or quiet modes and try it once again. If you frozen do not hear it, don't panic. Open up the cell phone over again and stare towards the top of the LCD. You'll see what looks approaching two undersize gold feet. These are not making communication near the delegate (that's screwed into the protection). Very vastly exceedingly carefully, tip them up honourable a minor and proximate the protection once more. Try the utterer. If you did everything correctly, you should perceive thing upcoming out of it. Now replace the hinges, screws, and gaoler covers and hold in the highest regard your work! Send a work of art to me at and I'll position it to the ikon gallery!

If you necessitate to see pictures of anything delineated above, satisfy go to my website (listed down), chink on 'Installations', and the decent PDF wallet. There is no costs for this. After clicking on the file, you'll have the PDF pop up on your blind near pictures fixed.

Disclaimer: The Phone Guy Online claims no susceptibility for patrons winning unconnected their phones. The pictures and remit provided herein are to be in use as a conduct. Even tho' we furnish these instructions, we immobile suggest taking your electronic equipment to a accustomed nonrecreational should you feel any convolution some. Through our experience, we know that not all phones act in precisely the one and the same rage (ie: a miniscule "rigging" may be essential with some after-market frills).